Download >> Download Cetol 23 application guide
Read Online >> Read Online Cetol 23 application guide
sikkens cetol 1 colors
sikkens application guide
sikkens cetol 23 review
sikkens cetol 23 plus dealers
cetol maintenance coat
cetol 23 plus reviews
cetol maintenance
how to apply sikkens cetol marine
Generously apply a cleaning solution of four (4) ounces of 100% powered Tri-Sodium phosphate (TSP) or phosphate-free substitute with one (1) quart of liquid bleach and three (3) quarts of water, to the wood Remove the old finish with an exterior wood finish remover, following the instructions that come with the product.
Cetol 1 & Cetol 23 PlusSystem: It is always recommended to perform a three (3) coat color and sheen test on a sample of the wood. Color can vary with application, porosity and type of wood. Intermix batches to ensure color consistency. After preparation, apply one (1) coat of Cetol 1 and two (2) coats of Cetol 23 Plus
Apply one coat of Cetol 23 Plus RE, Cetol Log & Siding, or Cetol Maintenance RE for standard applications. 2. For outdoor furniture and fence maintenance, apply one coat of Cetol 1 RE every one to two years. Maintenance Guidelines. Refer to Product Brochure for complete maintenance instructions. Asset No. 81865-P42
Preparation Instructions • All wood surfaces must be thoroughly clean, dry and free of dirt, grease, grime, mildew, mill glaze and previous coatings before applying Sikkens Proluxe Cetol 23 RE Wood Finish. • The best method to prepare vertical wood surfaces is to sand with 80-120 grit sandpaper. However, the following
The inclusion of translucent iron oxide pigments and UV absorbers gives excellent UV protection and color retention. Cetol 1 Wood Finish or Cetol 1 Re Wood. Finish MUST be applied to properly prepared wood as the basecoat before applying the Cetol 23 Plus RE Top Coat. *Specification data may vary with product color.
and water to remove all mold and mildew. Rinse and allow the wood to dry thoroughly. Apply a thin coat of Sikkens Cetol 23 to the cleaned area, and observe if the patch turns dark. If it does, the wall must be stripped of all the old stain per Sikkens instructions, either with sanding, media blasting, or chemical stripping and
Intermix batches to ensure color consistency. Do not apply when the surface is hot to the touch, when dew or frost is present, or expected within 5 hours of application, or in wet weather. Do not apply Cetol 1 over previously coated surfaces. After preparation, apply one (1) coat of Cetol 1, and two (2) coats of Cetol 23 plus,.
When using the, Cetol 1 & Cetol 23 Plus, old coatings must be completely removed before application. Use a wax-free chemical stripper, following the manufacturer's instructions, to strip down to bare wood. 2. In this case, the standard system – one (1) coat Cetol 1 and two (2) coats Cetol 23 Plus - is the best choice.
23 PLUS. APPLICATION GUIDE. Working With. Cetol. ®. I & Cetol. ®. 23 Plus. ? Preparation Procedures. Vertical Surfaces: New, Weathered, Uncoated Wood. The best method to prepare vertical wood surfaces is to sand with 80-120 grit sandpaper. However, an alternative to sanding for preparation is listed below.
Use the Cetol 1 for your base coat, but ABSOLUTELY apply the 2 coats of the Cetol 23 afterwards. This is a coating system. Applying the Cetol 1 without the Cetol 23 is just a waste of money IMHO. Sikkens (akzo nobel) suggest a single base coat of Cetol 1, followed by a top coat of Cetol 23 and then an
http://wxchzhp.mybb.social/viewtopic.php?id=155 http://www.texpaste.com/n/nuklbfi2 http://clashroyaledeckbuilder.com/viewDeck/1578284 http://www.tulugarfavorito.com/social/m/feedback/view/Bench-lathe-bv20-instructions-not-included-cast http://lothkco.rolbb.ru/viewtopic.php?id=57